Bienvenue sur le forum de la ZiGate !

Ici, nous échangeons sur les produits ZiGate (matériellement) et les firmware.

Pour que vous puissiez gagner du temps, je vous conseille de visiter, dans un premier temps, les forums et documentations des plugins et box domotique que vous avez choisi :

Jeedom :

Forum : https://community.jeedom.com/
Plugin ZiGate : https://github.com/Jeedom-Zigate/jeedom-plugin-zigate
Plugin Abeille : https://github.com/KiwiHC16/Abeille + http://kiwihc16.free.fr/

Domoticz :

Forum Francophonehttps://easydomoticz.com/forum/viewforum.php?f=28
Forum Anglophonehttps://www.domoticz.com/forum/viewforum.php?f=68
Développeur: @pipiche38 disponible sur keybase.io en chat

EEdomus :

Forum : https://forum.eedomus.com/

Home-assistant :

Plugin : https://github.com/doudz/homeassistant-zigate
Zigpy : https://www.home-assistant.io/integrations/zha/

Veuillez pour créer des messages et des sujets de discussion.

nouvelle installation sur RPI4 et GPIO2 Non OK

bonjour à tous

J'essai depuis hier de configurer ma pizigate sans succés..

quand je lance le test j'ai ce resultat :

RPI Model searching ...

All it's OK

Verifying /boot/cmdline.txt ...

+ /boot/cmdline.txt seems to be OK

Searching /dev/serial0...

lsof: WARNING: can't stat() fuse.gvfsd-fuse file system /run/user/1000/gvfs

Output information may be incomplete.

+ Port : /dev/serial0 is not used

Verif GPIOs ...

+ GPIO 0 (RESET) --> OK

- GPIO 2 (FLASH) --> NOK

Config GPIOs ...

+ GPIO 0 (RESET) --> OK

- GPIO 2 (FLASH) --> NOK

Opening : /dev/serial0 ...

+ /dev/serial0 opened --> OK

+ Packet 01 02 10 10 02 10 02 10 10 03 sent --> OK

- No packet received - size sent : 11 - error : 11

pi@raspberrypi:~/PiZiGate-tools/test $

 

Voila aussi les fichiers de config

mdLine

console=tty1 root=PARTUUID=d9e5a985-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles

config

# For more options and information see

# http://rpf.io/configtxt

# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible

# and your display can output without overscan

#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console

# goes off screen, and negative if there is too much border

#overscan_left=16

#overscan_right=16

#overscan_top=16

#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus

# overscan.

#framebuffer_width=1280

#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1

#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in

# DMT (computer monitor) modes

#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or

# no display

#config_hdmi_boost=4

# uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.

#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on

#dtparam=i2s=on

#dtparam=spi=on

# Uncomment this to enable infrared communication.

#dtoverlay=gpio-ir,gpio_pin=17

#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)

dtparam=audio=on

[pi4]

# Enable DRM VC4 V3D driver on top of the dispmanx display stack

dtoverlay=vc4-fkms-v3d

max_framebuffers=2

[all]

#dtoverlay=vc4-fkms-v3d

dtoverlay=w1-gpio

enable_uart=1

 

Quelqu'un à une idée ?

 

Merci

Translate »